Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
Just about every person has their own individual theory on the subject of How to Install a Bathtub.
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old bathtub is readily obtainable, the job can relocate rapidly; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to vacate the old bathtub and embeded in the brand-new one. Make sure you have certified yourself for the task and also fit attempting it. Rather than employing a service provider to take control of a halfway-completed task, it is far better to consider employing one before you start. Possibilities are you might require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your bathroom if you have actually currently purchased a brand-new bathtub and don't need to alter the setup of your previous water system pipes.
Your devices and also product checklist ought to comprise the following:
Preparing for the Setup
To start with, the supporting frame provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to stop strain on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is detach the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the limited gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Making use of both wood boards under its feet, position the bathtub in the required setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the level reviews degree.
To install faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; then do the same for the various other tap.
Turn on the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill the bathtub as well as additionally examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least once as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The previous type ought to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, creating the water to penetrate the wall surface in between the bath and the tiling, leading to complications with wetness as well as possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can break relatively very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about Tools You Need to Install a New Bathtub ? Create a review further down. We would be delighted to see your suggestions about this piece. We hope that you visit us again soon. For those who enjoyed our blog posting if you please remember to share it. Thanks so much for taking the time to read it.
Request immediate service. Report this page